manualshive.com logo in svg

Farm King Model 1050, Operator And Parts Manual

Share
Download
Farm King Model 1050 Operator And Parts Manual Download Page 48

46

Assembly - 10" Backsaver Auger

Figure 67

With the strap (Item 1) 

[Figure 67]

 installed around the

center tube section and connected to an approved

lifting device, raise the tube assembly high enough to

allow the undercarriage to be moved under the tube

assembly.

Figure 68

Move the undercarriage into position below the tube

assembly 

[Figure 68]

.

Figure 69

Align the RH & LH undercarriage arms with the

mounts (Item 1) 

[Figure 69]

 on the bottom tube

section (both sides).

Figure 70

Remove the two 3/8” x 1-1/4” bolts (Item 1) 

[Figure

70]

, 3/8” lock nut and 3/8” flat washers from the

undercarriage tie plate.

NOTE: Loosening the undercarriage tie plate will allow

the RH & LH undercarriage arms to be moved

during installation to the tube assembly.

B-0376A

1

B-0666

B-0663

1

B-0667

1

Summary of Contents for Model 1050















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands