Farm King Model 1050 Operator And Parts Manual Download Page 69

Page: 69 / 174

Operation - 10" Backsaver Auger

Figure 118

Turn the handle (Item 1)

[Figure 118]

clockwise to

raise the hitch or counterclockwise to lower the hitch.
Lower or raise the Backsaver Auger hitch until aligned

with the tractor’s drawbar.
Move to the operator’s seat, start the engine and

release the parking brake.

Move the tractor backwards, aligning the drawbar

hitch pin hole with the Backsaver Auger hitch pin

hole(s).

Stop the tractor and leave operator’s position. (See

“Leaving The Operator’s Position” on page 66.)

NOTE: Always use a hitch pin of adequate size and

strength and a retaining pin with a locking

device.

Figure 119

Install the hitch pin (Item 1)

[Figure 119]

and retaining

pin to securely fasten the Backsaver Auger hitch to

the tractor drawbar.
Attach the safety chain (Item 2)

[Figure 119]

around

the drawbar.

B-3021

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when

connecting and disconnecting equipment.

B-0530

Summary of Contents for Model 1050















































































































































































Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands

Farm King Model 1050, Operator And Parts Manual

Search results

Summary of Contents for Model 1050

Reviews:

Related manuals for Model 1050

Brands by name

Popular brands