Expert SmartTurn Installation And Operating Instructions Manual Download

Page: 61 / 70

Turntable control SmartTurn

Faults

Dok-ID:EXPERT-0003-EN-2011

6.3.4 Change mode (changed rotary mode)

The mode deviates from the saved mode or impermissible level
change on input E4 "Mode"

Change from position 9 to position 1-4 or vice versa on rotary
switch S1.

Possible causes

Measures

Mode change from:

- Continuous run in reverse mode

- Special to reverse mode (change from position 9 to
1-4 on rotary switch S1)

Reverse mode:



Turn drive roller (position encoder) a min. 45

degrees outside of the 0-position in the movement
range between the positions "Front" and "Back".

Mode change from:

- Reverse mode to continuous mode

- Special to continuous mode (change from position 9
to 1-4 on rotary switch S1)

- Continuous to special mode (change from position 9
to 1-4 on rotary switch S1)

Continuous mode, special mode:



None

Reset fault

NOTE!

Eliminate cause.



Unscrew the cover on the turntable control unit.



Press the reset button for at least 3 s.



System fault LED goes out.



Turn the turntable several times at operating speed.

Press the reset button and the default values will be used for
turntable control.

NOTE!

Comply with the supplemental instructions in the
section ->

Commissioning

Pos : 6. 13 /SmartT urn/SmartTur n-Neu-02. 2011/ 6. 3. 5 Wechs el Dr ehric ht ung @ 3\ mod_1297948833478_38.doc @ 26389

Summary of Contents for SmartTurn







































































Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands

Expert SmartTurn, Installation And Operating Instructions Manual

Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands