manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 52

 

Turntable control SmartTurn 

 

Installation and commissioning 

 

 

52 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

5.4.1  Re-commissioning in the plant 

When re-commissioning the turntable in the plant the settings 
made during the commissioning process must be checked and any 
adaptations to local conditions must be executed. 

 

 

Re-commissioning sequence 

1.

 

Switch on the operating voltage. 

2.

 

Turn the turntable several times at creep speed. 

3.

 

Check direction of motor rotation, drive roller. 

4.

 

If necessary change direction of motor rotation and set 
clockwise / counter-clockwise drive roller direction. 

5.

 

Press the reset button 3s - system fault LED goes out 

6.

 

Turn the turntable several times at operating speed. 

 

If the turntable stops several times without fault in the 0-position, 
the self-adjustment and re-commissioning are concluded. 

 

 

NOTE! 

After first-time operation of the turntable with the 
customer load, or after changes to the load, 
overrun faults could occur. In this case it is 
necessary to turn the turntable several times at 
operating speed until the turntable controller has 
concluded the optimization process. 

 

 

Pos : 6. 1 / Smart Tur n/ 6 Stör ung en @ 1\ mod_1221477905554_38.doc @ 8442 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands