manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 12

 

Turntable control SmartTurn 

 

Safety 

 

 

12 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

Pos : 2. 8 / Smart Tur n/ 2._U mwelts chutz  @ 1\ mod_1219048921572_38.doc @ 6898 

 

2.4  Environmental protection 

 

 

CAUTION! 
Environmental hazard due to incorrect 
handling! 

Incorrect handling of environmentally hazardous 
substances, particularly improper disposal, can 
cause significant environmental damage. 

Therefore: 

–  Always comply with the instructions cited below. 

–  If environmentally harmful substances should 

inadvertently get into the environment, initiate 
suitable measures immediately. If in doubt notify 
the responsible municipal authority about the 
damage. 

 

Dispose of the controller as electrical and electronic waste. 

 

Pos : 2. 9 / St andardmodule/------Seitenumbr uch-------- @ 0\ mod_1192536092524_38. doc  @  116 

 Pos : 3 /SmartTur n/SmartT urn-N eu- 02.2011/3 Tec hnisc he D aten @  2\mod_1296727941342_38.doc @  25788 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands