Expert SmartTurn Installation And Operating Instructions Manual Download

Page: 62 / 70

Turntable control SmartTurn

Faults

Dok-ID:EXPERT-0003-EN-2011

6.3.5 Change mode (changed rotary direction)

Rotary direction deviates from the saved rotary direction or change
rotary direction right/left on switch S3.

Possible causes

Measures

Reverse mode / change S3

Reverse mode:



Turn drive roller (position encoder) a min. 45

degrees outside of the 0-position in the
movement range between the positions "Front"
and "Back"

Continuous mode / change S3

Continuous mode – special mode:



None

Reset fault

NOTE!

Eliminate cause.



Unscrew the cover on the turntable control unit.



Press the reset button for at least 3 s.



System fault LED goes out.



Turn the turntable several times at operating speed.

Press the reset button and the default values will be used for
turntable control.

NOTE!

Comply with the supplemental instructions in the
section ->

Commissioning

Pos : 6.14 /SmartT urn/SmartTur n-Neu-02.2011/6.3.6.Wechs el R astg ang @ 3\mod_1315558981688_38.doc @ 30170

Summary of Contents for SmartTurn







































































Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands

Expert SmartTurn, Installation And Operating Instructions Manual

Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands