manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 58

 

Turntable control SmartTurn 

 

Faults 

 

 

58 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

6.3.1  Sensor fault (sensor defect)  

 

 

Possible causes 

Measures 

Sensor is defective 

Check sensor and replace if necessary 

Position encoder is defective or is not in the 
detection range of the sensor 

Check the position sensor, replace if necessary 

Sensor cable is defective or loose 

Check the position sensor, replace if necessary 

Sensor cable has been inadvertently unscrewed 

Screw on the sensor cable 

 

 

 

Reset fault 

 

 

NOTE! 

Eliminate cause. 

 

 

 

Unscrew the cover on the turntable control unit. 

 

 Press the reset button for at least 3 s. 

 

System fault LED goes out. 

 

Turn the turntable several times at operating speed. 

Press the reset button and the default values will be used for 
turntable control. 

 

Pos : 6. 10 /SmartT urn/SmartTur n-Neu-02. 2011/ 6. 3. 3 Kurzsc hl uss am ausgang @ 3\ mod_1315561035885_38. doc @ 30187 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands