manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 6

 

Turntable control SmartTurn 

 

General Information 

 

 

6 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

1.2  Explanation of symbols  

 

Warnings 

Warnings are indicated by symbols in this operating manual. The 
warnings are introduced by signal words that express the scope of 
the hazard.  
The warnings must be strictly heeded, you must act prudently to 
prevent accidents, personal injury, and property damage. 

  

 

DANGER! 

… indicates an imminent dangerous situation that 
can result in death or serious injury if it is not 
avoided. 

 

 

 

WARNING! 

… indicates a possible dangerous situation that can 
result in death or serious injury if it is not avoided. 

 

 

 

 

CAUTION! 

… indicates a possible dangerous situation that can 
result in  minor injury if it is not avoided. 

 

 

 

 

CAUTION! 

… indicates a possible dangerous situation that can 
result in material damage if it is not avoided. 

 

 

 

Tips and recommendations 

 

 

 

NOTE! 

... indicates useful tips and recommendations, as 
well as information for efficient and trouble-free 
operation. 

 

  

 

Pos : 1. 5 / St andardmodule/------Seitenumbr uch-------- @ 0\ mod_1192536092524_38. doc  @  116 

 Pos : 1.6 /Standardmodule/1 Allgemeines/1.3 H aftungsbesc hränkung @ 0\mod_1192534313566_38.doc  @ 96 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands