manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 50

 

Turntable control SmartTurn 

 

Installation and commissioning 

 

 

50 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

Pos : 5. 19 /SmartT urn/SmartTur n-Neu-02. 2011/ 5. 2 Abl auf der Inbetriebnahme @ 3\ mod_1297939267607_38.doc @ 26287 

  

Commissioning sequence 

 

 

 

Fig. 23 Example: Movement range  

 

1 

Movement range 

 
 
“B”    backward 
 
“F”    forward 

 

 

 

1.

 

Turn drive roller (position encoder) in the movement range (1), 
at least 45 degrees outside of the 0-position. The turntable will 
then be between the positions 

"Front"

 and 

"Back"

 (only 

necessary in reverse mode). 

2.

 

Set mode - lock movement drive roller on rotary switch S1. 

3.

 

Set clockwise rotation / counter-clockwise rotation - drive roller 
switch S3. 

4.

 

Switch on the operating voltage. 

5.

 

Press "Reset" button 3 s – LED system fault will go out. 

6.

 

Turn the turntable several times at operating speed 

 

 

NOTE! 

If the turntable stops several times without fault in 
the 0-position the self-adjustment and the 
commissioning processes are concluded. 

The settings of S1 and S3 are marked on the inside 
of the cover at commissioning. 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands