manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 9

 

 

Turntable control SmartTurn 

Safety 

 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

9 

 

2  Safety 

 

This section provides an overview of all the important safety 
aspects for optimal protection of personnel, as well as for safe and 
trouble-free operation. 

Significant hazards can occur if the handling instructions and 
safety instructions in this manual are not complied with. 

 

Pos : 2. 2 / Smart Tur n/ 2__Mont age-  und Betriebs anl eit ung- Drehtis che beac ht en @  1\mod_1219047563353_38.doc  @  6887 

       

Comply with the instructions in the 
Installation and Operating Manual - 
Turntables 

 

 

 

DANGER! 
Danger of severe or fatal injuries! 

Therefore: 

–  Strictly ensure that you have read the 

Installation and Operating Manual - Turntables 

 

 

 

 

 

NOTE! 

The safety instructions in the Installation and 
Operating manual - Turntables, and in the technical 
documentation must be strictly complied with. 

The turntable controller is included as a component 
in the scope of delivery of a turntable. 

 

 

Pos : 2. 3 / St andardmodule/------Seitenumbr uch-------- @ 0\ mod_1192536092524_38. doc  @  116 

 Pos : 2. 4 / Smart Tur n/ 2._Verant wortung des  Betr eibers @ 1\ mod_1219046166750_38. doc @  6854 

 

2.1  Responsibility of the customer 

The device is used in industrial applications. Consequently the 
owner of the device is subject to legal industrial safety obligations.  

In addition, the customer is responsible to ensure that the system 
is always in technically faultless condition. 

Compliance with the instructions in the operating manual is the 
prerequisite for trouble-free operation and the fulfillment of possible 
guarantee claims.  

The operating manual contains important service instructions 
therefore it must be kept in a safe location.  

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands