manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 26

 

Turntable control SmartTurn 

 

Structure and function 

 

 

26 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

With the reversal of rotary direction, the rotary direction check of 
the drive roller can be reversed. 

Clockwise is the factory setting. 

If the rotary direction of the drive roller does not agree with the 
setting, then this is detected as a fault at activation and the fault 

"Wrong rotary direction"

 is triggered. 

If the device is replaced the rotary direction must be set 
appropriately.  

 

 

NOTE! 

Additional instructions in the section -> System 
faults – wrong rotary direction forward / backward. 

 

 

Pos : 4. 20 /SmartT urn/4. 2. 5_d Gr afi k - Beis piel mi t t ext  @ 1\ mod_1219402942566_38.doc @ 7273 

 

 

Fig. 7 Rotary direction example 

Example: 

Turntable with drive roller and left ascending groove. 
Counter-clockwise rotation should occur on the turntable 
plate at 

"Forward on"

 activation. 

Connect motor so that clockwise rotation occurs at 
"Forward on" activation on the drive roller. 

Setting the drive roller rotary direction: 

Clockwise

 

 
 
 
 
1 

Counter-clockwise rotation of the turntable plate 

2 

Clockwise rotation of the drive roller 

 

 

 

Pos : 4. 21 /SmartT urn/SmartTur n-Neu-02. 2011/ 4. 3+4.3.1+ 4. 3. 2 Ansc hl üsse @  3\mod_1296814252485_38.doc  @  25967 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands