manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual, Page: 63 / 70

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 63

 

 

Turntable control SmartTurn 

Faults 

 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

63 

 

6.3.6  Changed lock angle  

 

Lock angle setting deviates from the saved lock angle setting or 
change of the lock angle on switch S1. 

 

 

Possible causes 

Measures 

Reverse mode / continuous mode 

 

Continuous mode, reverse mode 

  None 

 

 

Reset fault 

 

 

NOTE! 

Eliminate cause. 

 

 

 

Unscrew the cover on the turntable control unit. 

 

 Press the reset button for at least 3 s. 

 

System fault LED goes out. 

 

Turn the turntable several times at operating speed. 

Press the reset button and the default values will be used for 
turntable control. 

 

 

NOTE! 

Comply with the supplemental instructions in the 
section -> 

Commissioning

 

 

Pos : 6. 15 /SmartT urn/SmartTur n-Neu-02. 2011/ 6. 3. 7 F alsc he Drehricht ung @ 3\ mod_1297948951646_38.doc @ 26406 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments