Expert SmartTurn Installation And Operating Instructions Manual Download

Page: 15 / 70

Turntable control SmartTurn

Structure and function

Dok-ID:EXPERT-0003-EN-2011

Pos : 4. 2 / Smart Tur n/SmartT urn-N eu- 02.2011/4. 1. 1 Ger ät ebesc hr eibung @ 2\ mod_1296729895005_38. doc @ 25805

4.1.1 Device description

Sensor, Fig. 1

The sensor is equipped with:



A connection for the control unit.



One green LED and two yellow LEDs.

All three LEDs are illuminated when the sensor is connected to the
control unit.

Control unit, Fig. 2

The controller is equipped with:



Four connections for 24 V supply and PLC signals (X1), power

unit (X2), sensor (X3), diagnostics connection (X4).



Eight LEDs that enable fast and easy diagnosis. Faults are

indicated through flashing red LEDs. More information about
faults is provided in the

section -> Faults

LED

Function

Color

System fault

Red

Overrun forward

Red

0-position

Yellow

Overrun backward

Red

End lock angle

Red

Start forward on

Yellow

Start backward on

Yellow

Not assigned

24 V power supply

Green

More extensive diagnoses is possible with the diagnostics
software, via the diagnostics connection (X4).

Pos : 4. 3 / Smart Tur n/SmartT urn-N eu- 02.2011/4. 2 Funkti onsbesc hrei bung @ 2\ mod_1296730371811_38. doc @ 25822

Summary of Contents for SmartTurn







































































Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands

Expert SmartTurn, Installation And Operating Instructions Manual

Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands