Expert SmartTurn Installation And Operating Instructions Manual Download

Page: 10 / 70

Turntable control SmartTurn

Safety

Dok-ID:EXPERT-0003-EN-2011

Pos : 2. 5 / Smart Tur n/ 2_ Personalanf orderungen @ 1\ mod_1219047099489_38. doc @ 6876

2.2 Personnel requirements

2.2.1 Qualifications

WARNING!
Danger of injury due to insufficient
qualification!

Improper handling can cause serious injury or
material damage.

Therefore:

– Only have activities performed by personnel

who are qualified to perform these activities.

Only persons from whom it can be expected that they reliably
execute their work are considered as personnel. Persons whose
capability to react is impaired, for instance through drugs, alcohol,
or medication, are not approved.



Comply with age-specific and job-specific regulations that are

applicable at the installation site when selecting personnel.

Pos : 2. 6 / St andardmodule/------Seitenumbr uch-------- @ 0\ mod_1192536092524_38. doc @ 116

Pos : 2.7 /SmartTur n/2_ Besti mmungsgemäß e Ver wendung @ 1\mod_1219049844784_38.doc @ 6909

Summary of Contents for SmartTurn







































































Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands

Expert SmartTurn, Installation And Operating Instructions Manual

Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands