manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 59

 

 

Turntable control SmartTurn 

Faults 

 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

59 

 

6.3.2  Short circuit at output 

 

 

Possible causes 

Measures 

Activated contactor coil defective 

Check the contactor coil, replace if necessary 

Excessive power consumption of the activated 
contactor coil 

Only use contactor coils with a max. power 
consumption of 14 W at 24 V DC 

Contactor coil without protective circuit 

Always wire contactor coils with Varistor protective 
circuit 

Short circuit due to wiring fault 

Check wiring and change 

 

 

 

Reset fault 

 

 

NOTE! 

Eliminate cause. 

 

 

 

Unscrew the cover on the turntable control unit. 

 

 Press the reset button for at least 3 s. 

 

System fault LED goes out. 

 

Turn the turntable several times at operating speed. 

Press the reset button and the default values will be used for 
turntable control. 

 

 

 

NOTE! 

Comply with the supplemental instructions in the 
section -> 

Commissioning

 

 

 

 

Pos : 6. 11 /SmartT urn/SmartTur n-Neu-02. 2011/ 6. 3. 2 U ngültige Sensor daten @ 3\ mod_1297944340064_38. doc @  26355 

 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands