manualshive.com logo in svg

Expert SmartTurn, Installation And Operating Instructions Manual

Share
Download
Expert SmartTurn Installation And Operating Instructions Manual Download Page 53

 

 

Turntable control SmartTurn 

Faults 

 

 

Dok-ID:EXPERT-0003-EN-2011

 

 

53 

 

6  Faults 

Possible fault causes and the tasks to correct these faults are 
described in the following section.  

Contact the manufacturer if there are faults that cannot be 
corrected by following the instructions below; see the service 
address in the Appendix. 

 

Behavior in the event of fault 

The following always applies: 

1.

 

Determine the cause of the fault. 

2.

 

Immediately inform the responsible parties at the installation 
site of the fault. 

3.

 

Have authorized specialists eliminate the fault. 

  

 

Pos : 6. 2 / Smart Tur n/ 6.1 Stör ung en- Sicherheit @ 1\ mod_1219733798505_38. doc @ 7494 

 

6.1  Safety 

 

 

Personnel 

  Some tasks should only be executed by experts with special 

training or by the manufacturer. 

  Only qualified electricians should perform work on the electrical 

equipment. 

  

 

  Pos : 6.3 /SmartTur n/6.2 Ablaufstörungen @  1\mod_1219739605025_38.doc  @  7505 

 

6.2  Sequence faults 

Sequence faults are faults that can occur during normal operation 
through brake wear, 

and/or due to impermissible turntable operation, e.g. due to 
overload, change in load, or incorrect activation of the brake and 
motor. 

 

NOTE! 

The fault tables below are provided to help you 
localize and rectify the fault. 

Or contact one of the EXPERT-TÜNKERS service 
addresses. 

 

 

Pos : 6. 4 / Smart Tur n/SmartT urn-N eu- 02.2011/6. 2. 1  Überlauf  Vorwärts  / R üc kwärts  @ 3\ mod_1297939864245_38.doc @ 26304 

 

6.2.1  Overrun forward / backward  

The fault is generated if the turntable does not come to a stop in 
the 0-position and overruns the 0-position by more than 8 degrees. 

The fault is also generated when the turntable is in the forward or 
backward position and an incorrect activation is executed by the 
PLC. 

Summary of Contents for SmartTurn







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands