Expert SmartTurn Installation And Operating Instructions Manual Download

Page: 25 / 70

Turntable control SmartTurn

Structure and function

Dok-ID:EXPERT-0003-EN-2011

Pos : 4. 18 /SmartT urn/4. 2. 5_b S3 @ 1\ mod_1219401222930_38. doc @ 7251

Rotary direction clockwise rotation - counter-clockwise
rotation, drive roller

Fig. 6

R = clockwise rotation (default value)

L = counter-clockwise rotation

The rotary movement of the turntable plate depends on the rotary
direction of the drive motor, and on the incline of the drive roller.

The turntable controller checks whether the forward/backward
activation and the rotary direction of the drive roller agree.

Clockwise

In this setting the turntable controller expects drive roller / position
encoder rotation to the right (clockwise) at "

Forward on"

For

"Backward on"

left (counter-clockwise) rotation of the drive

roller / position encoder is expected.

Counter-clockwise

In this setting the turntable controller expects drive roller / position
encoder rotation to the left (counter-clockwise) at "

Forward on"

"Backward on"

right (clockwise) rotation of the drive roller /

position encoder is expected.

Pos : 4. 19 /SmartT urn/SmartTur n-Neu-02. 2011/ 4. 2. 5_c z u S3 @ 3\ mod_1296814152452_38. doc @ 25950

Summary of Contents for SmartTurn







































































Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands

Expert SmartTurn, Installation And Operating Instructions Manual

Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands