Expert SmartTurn Installation And Operating Instructions Manual Download Page 49 | Manualshive

Page: 49 / 70

background image

Turntable control SmartTurn

Installation and commissioning

Dok-ID:EXPERT-0003-EN-2011

49

5.4

Commissioning

NOTE!

The turntable is commissioned in the factory by
EXPERT-TÜNKERS.

When the turntable is commissioned it is tested and the mode is
adjusted to customer specifications in reverse mode, continuous
mode or special mode.

When the operating voltage on the turntable is switched on,
simultaneously input E4 must be connected with 0 V for reverse
mode and special mode, or with 24 V for continuous mode.

Subsequent level change is not permissible and results in a system
fault.

Another commissioning process is only necessary when:



The control unit is replaced,



The mode is changed



or a system fault makes this necessary.

NOTE!

See section ->

System faults.

All data is saved in the control unit, failsafe. With the
commissioning process a default value specific to the lock
movement is used as switch-off angle. Thereafter deviation from
the optimal 0-position is determined and the switch-off angle is
determined for the next turn.

«
...
47
48
49
50
51
...
»

Summary of Contents for SmartTurn







































































Reviews:

No comments

Related manuals for SmartTurn

Brand: Neoi Pages: 77

Brand: Cocoon Pages: 28

Brand: PANODIC Pages: 8

Brand: Xoro Pages: 33

Brand: Giani Digital Pages: 38

Brand: Quadro Pages: 42

Brand: Reloop Pages: 20

Brand: Affirmative Pages: 104

Brand: Fenton Pages: 17

Brand: bq Pages: 68

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 3

Excite AT305SE-T32

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 82

Brand: Toshiba Pages: 82

Brand: Toshiba Pages: 85

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands