Expert SmartTurn Installation And Operating Instructions Manual Download

Page: 56 / 70

Turntable control SmartTurn

Faults

Dok-ID:EXPERT-0003-EN-2011

Pos : 6. 6 / Smart Tur n/ 6.2.3 Ende Ras t winkel r eser ve erreic ht @ 1\ mod_1219744044028_38. doc @ 7538

6.2.3 End of lock angle reserve reached (end of lock angle reserve)

If the switch-off angle is more than 5 degrees outside of the lock
movement, the warning

"End lock angle"

and

"System fault"

are

output to the PLC simultaneously.

Do not continue to operate the turntable. Further operation can
cause damage to the drive elements.

CAUTION!
Switch-off over 5 degrees.

Further operation can cause damage to the drive
elements!

Therefore:

–

Do not continue to operate the turntable.

–

Eliminate the cause.

Possible causes:

Measures

Brake pads are worn or the brake is defective

Check the brake and replace it if necessary

Mech. damage on the turntable

Check turntable for mechanical damage

Reset fault

NOTE!

Eliminate cause.

Unscrew the cover on the turntable controller and press the reset
button for at least 3s.

Press the reset button and the default values will be used for
turntable control.

Summary of Contents for SmartTurn







































































Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands

Expert SmartTurn, Installation And Operating Instructions Manual

Search results

Summary of Contents for SmartTurn

Reviews:

Related manuals for SmartTurn

Brands by name

Popular brands