EWS UFS8000 Operating Manual Download Page 63

Page: 63 / 130

UFS8000

Alarms

8.3. Overview alarms

Shortened display

Description

Backup settings

The last programming changes are not stored. The previous programming
is loaded.
Check the parameters or load an back-up through a SD Card.

Default settings

The configuration files on the hard disk are disabled or unavailable
The controller has to be configured again or a back-up loaded.

Language file

The language file cannot be read. The English language will be loaded.
You can load a backup through a SD Card.

Font file

The font file cannot be read. The standard font will be loaded.
You can load a backup through a SD Card.

Multiple files

Multiple files can not be read. You can load a backup through a SD Card.

E-mail could not be sent

Maintenance

Maintenance has to be undertaken on the unit.

ROM settings

The configuration files on the hard disk are disabled or unavailable.
The controller has to be configured again or a back-up
loaded.

SD: Software Card

The SD card is not appropriate for the data logging or a back-up.
The SD card contains original software or “OEM” software.

SD: Card full

Not enough disk space on the SD card

SD: Not present

No SD card available or this does not comply with the specifications.

Power failure

The controller has been switched off.

Set clock

The clock must be set at a valid date/time.

Summary of Contents for UFS8000



































































































































Search results

Summary of Contents for UFS8000

Reviews:

EWS UFS8000, Operating Manual, Page: 63 / 130

Search results

Summary of Contents for UFS8000

Reviews: