manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 85 / 163

Share
Download
Elster EK280 Applications Manual Download Page 85

EK280 

Application Manual 

83 

 

7.3.2 

FE260 SIM card insertion and unlock 

The  SIM  card  must  only  be  inserted  and  if  applicable  unlocked  in  FE260  GSM/GPRS  versions.  For  other 
versions (Analog modem, Ethernet, ISDN) this Chapter can be skipped. 
SIM card installation varies according to the GSM/GPRS module used in the FE260: 

 

From around mid-2014: "ECM-GW-120" (see chapter 7.3.2.1) 

 

Older versions: Integra "M2106+" or "M2106B" (see chapter 7.3.2.2) 

 

 

7.3.2.1  SIM in the GSM/GPRS-module "ECM-GW120" (from mid-2014)  

a) SIM card insertion 

 

 

Danger! 

Ensure the mains voltage is disconnected before opening the FE260 housing, ensure it 
is not turned back on and verify that there is no voltage. 

 

 

Remove the four screws from the top of the FE260 and open it. 

 

To unlock the SIM card holder slide the metal 
strap to the right and open flap. 

 

Slide SIM into the flap of the

  

SIM card holder. 

 
 
 
 
 
 
 
 
 
 

 

Close flap again and lock (slide metal strap under slight pressure to the left). 
The chamfered edge of the SIM must now be located at bottom left as shown. 

 

Screw the FE260 housing back on. 

 

b) If necessary, unlock the SIM card (enter the PIN) 

If the inserted SIM card's PIN ("Personal Identification Number") is activated, carry out the following instructions 
to unlock it: 

 

Move the cursor to the "

Serv.

" tab in the EK280's display, then to  

Interfaces > Terminal interface

 

> GSM & GPRS > PIN

 

 

Press the 

ENTER

 key and enter the first PIN digit using the 

 and 

arrow keys. 

 

i 

The PIN must be entered right-aligned in the EK280! 

 

 

Move the cursor through the next digits using the 

 key and enter them. 

 

After entering the last digit press the 

ENTER

 key, to save the input. 

 

Under "

P.Sta

" the "

Pin New

" is now ready for confirmation.  

If "

P.Sta

" is not displayed, move the cursor down using the 

 arrow keys. 

 

As soon as a communications time window is opened via the modem, the new PIN is used. After a 
few seconds, under "

P.Sta

" the message "

Pin OK

" is displayed if the correct PIN was entered, or the 

message "

Pin Error

" if the PIN was incorrectly entered. 

 

 

Figure 11: 

SIM card slot on the ECM-GW120 modem

 

 

 Metal strap to the right: SIM unlocked (open)  

  Metal strap to the left: SIM locked (closed) 

After installation, the chamfered edge of the 
SIM is located at bottom left.

 

Summary of Contents for EK280




































































































































































Reviews:

No comments