Elster EK280 Applications Manual Download Page 77

Page: 77 / 163

EK280

Application Manual



Press the button "

", after which the window "Settings for the Ethernet adapter" will open.

Please input here the values your network needs for
- IP address
- Gateway address
- Subnet mask
- TCP port
(the values given here are only

examples



After pressing

of the button “

" the parameters are transmitted to the Ethernet adapter. The

successful end of the transmission is signaled with the following message:

In the header of the dialog box "Settings for Ethernet adapter" the hardware and the firmware version of
the Ethernet adapter are shown:



Terminate the "ModemIni" program



Now disconnect the power to EM260.



Disconnect the USB parameterizing cable from EM260.



Push fit the J1 in the uppermost position (see operating instructions for
the EM260, Section 10 "Jumper" and photograph on the right).



Make sure that the EM260 is connected in accordance with Section
7.2.1 to the EK280.



Close housing of EM260

Summary of Contents for EK280




































































































































































Search results

Summary of Contents for EK280

Reviews:

Elster EK280, Applications Manual, Page: 77 / 163

Search results

Summary of Contents for EK280

Reviews: