Elster EK280 Applications Manual Download Page 55 | Manualshive

Page: 55 / 163

Elster EK280 Applications Manual Download Page 55

EK280

Application Manual

53

7.1.4

GPRS with ComFTP

For an active ComFTP application, data is read from the EK280 by the modem and transferred independently
using the PUSH principle from the ComFTP modem to a FTP server set up beforehand. This function must be
commissioned separately in the modem itself (separate descriptions available).
In addition to the FTP function, the standard GSM/CSD mode (PULL principle) is also possible by calling a
data telephone number (albeit not at the same time).

i

The active ComFTP application will incur costs due to continuous data volume transmission via
a mobile network. Estimate adequate reserve for this. Talk to your provider to obtain an
economical tariff. Switching off roaming can also help to reduce costs. Optimization of these
factors is your responsibility.

i

Wireless networks can be disrupted, therefore one hundred percent data transfer cannot be
guaranteed in any case.

i

This application works only with a modem with "ComFTP" option. This option
must be requested at the time of ordering of the EK280. Compatibility is indicated
by the field marked "ComFTP" on the EK280 modem's label.

7.1.4.1 Prerequisites for operation with ComFTP

The following conditions must be fulfilled to enable operation of the ComFTP application:



The ComFTP server must be configured. It is vital to ensure that adequate free space is available.
The directories used for standard response and archive transfer must exist.



ComFTP server maintenance must be assured - the data must be processed in a timely manner. If
this is overlooked, data loss may occur. Talk to your IT department or relevant service provider about
this.

7.1.4.2 Preparation

Initial conditions:



The SIM card is inserted and unlocked as described in Chapter 8.1.1.



For the following parameterization the EK280 power supply must first be switched off.

7.1.4.3 Opening the customer lock

In order for ComFTP to read data from the EK280 and save it on the server, at least one EK280 lock must be
permanently open. For this purpose it is recommended to use the customer lock, as this contains the least
write permissions and therefore avoids the risk of unauthorized parameter updates.



Move the cursor to the "

Serv.

" tab in the EK280's display, then to

Device settings > Access > St.CL

(customer lock status).



If "

open

" is displayed below

St.CL

the customer lock is already open.



If "

locked

" is displayed under

St.CL

move the cursor over to

Cod.C

and after pressing the

ENTER

key on the keypad, enter the single digit customer lock with the keypad.
The default customer lock setting is "

0

". After pressing

ENTER

to commit the change, check that

"

open

" is now displayed under

St.CL

.



In order to ensure the customer lock is not automatically closed again, Move the cursor further down
to

AutCL

and make sure that "

0 minutes

" is displayed here.



If "

0 minutes

" is not displayed under

AutCL

, set the value after pressing the

ENTER

button on the

keypad to "

0

" and save the input with the

ENTER

button.

«
...
53
54
55
56
57
...
»

Summary of Contents for EK280




































































































































































Reviews:

No comments