Elster EK280 Applications Manual Download Page 121

Page: 121 / 163

EK280

Application Manual

119

Display Description

The port for server connection is not defined.

The target name or port is not defined.

The other party has disconnected.

The communication link to the network was lost, after a communication link to the remote party
was already established.

The phone number of the SMS service center is wrong or missing at the SIM card.
The mobile service provider must be contacted.

The APN password or APN user name is wrong.

The APN parameters are already in use by another mobile phone subscriber.

Failed to establish communication link to the remote terminal
Possible cause: i.e. blocked by remote terminal firewall.

The remote terminal did not respond (timeout)
Possible causes: The remote terminal machine is switched off or the remote terminal has not
been started.

The remote terminal reports "unknown device type".

The EK280 does not understand the remote terminal response.
Possible causes: E.g. transfer error.

Sending error: When attempting to send data to the remote terminal, the modem reported an
error.

255

Unknown error

7.5.4

Status of remote terminal "SDst"

Display Description

No connection started to a remote terminal.

No valid remote terminal specified. Check the related EK280-phonebook entry.

Connection to remote terminal is in progress.

Remote terminal is busy.

Connection to remote terminal established.

Disconnection from remote terminal in progress.

Disconnection from remote terminal finished.

Remote terminal not reached. Check the related EK280-phonebook entry or check the
readiness for reception of the remote terminal.

Remote terminal refused the connection. Check the related EK280-phonebook entry or check
the readiness for reception of the remote terminal.

Connection to remote terminal aborted during communication.

Summary of Contents for EK280




































































































































































Search results

Summary of Contents for EK280

Reviews:

Elster EK280, Applications Manual, Page: 121 / 163

Search results

Summary of Contents for EK280

Reviews: