manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 38 / 163

Share
Download
Elster EK280 Applications Manual Download Page 38

EK280 

Application Manual 

36 

 

Setting up period length and pulse duration 

i 

Parametrization of the period length and the pulse duration via the EK280 keyboard is only 
possible with software version 2.20 or later. 
Older software versions may be programmed using enSuite via "

Parameterize online

" > 

"

Parameters

"

 and the paths described (see Chapter 6.2.1, 0)  

 

i 

The cycle duration and the pulse duration can be set as a multiple of 125 ms for each output.  
The cycle duration must always be longer than the pulse duration. 
The maximum output frequency is 4 Hz  

 

Examples: 

Period 

Pulse width 

Output frequency 

Per.O 

in ms 

PW.O 

in ms 

in Hz 

2 

250 

1 

125 

4 

4 

500 

2 

250 

2 

8 

1000 

4 

500 

1 

80 

10000 

40 

5000 

0.1 

 

 

When in the corresponding output menu press the button 

 until 

"PerO1"

, 

"PerO2"

,

 "PerO3"

 or. 

"PerO4"

 is displayed. 

 

Press the ENTER 

 button. The actual parameterized value flashes. 

 

Move the cursor to the digits using the 

 or 

 arrow keys and update them using the 

 or 

 arrow 

keys to set the desired period. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

 

When in the corresponding menu press the button 

 repeatedly until 

"PW.O1

", 

"PW.O2"

, 

"PW.O3"

 

or "

PW.O4"

" is displayed. 

 

Press the ENTER 

 button. The actual parameterized value flashes. 

 

Move the cursor to the digits using the 

 or 

 arrow keys and update them using the 

 or 

 arrow 

keys to set the desired period. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

Setting up access permissions for the output parameters: 

i 

Parameterization of access authorizations for the output parameters via the EK280 keyboard 
is not possible! 
Parameterization may be done with enSuite in 

"Parameterize online" > "Parameters" > 

"Outputs" > "Output 1" to Output 4"

.  

 

Summary of Contents for EK280




































































































































































Reviews:

No comments