manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 20 / 163

Share
Download
Elster EK280 Applications Manual Download Page 20

EK280 

Application Manual 

18 

 

4.1 

LF Pulse generator (reed contact) 

4.1.1 

Connection 

 

 

Danger! 

For EK280 with internal power supply, the mains voltage must be switched off before 
opening the housing, ensure it is not turned back on and verify that there is no voltage. 

 

 

 

 

 

 

 

 

 

 

DE1 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+ 

- 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

     

Pulse generator 

NF  

(Reed contact) 

                     

 

 

 

 

Connect the gas meter's low frequency pulse generator (reed contact) to terminal "DE1" of the 
EK280. 

 

Release the input 1 (terminal "DE1") calibration seals. 

4.1.2 

Parameterization 

Parameterization is carried out via the keyboard on the EK280.  
Alternatively, parametrization can be carried out using the 

enSuite

 program. The paths which are subsequently 

described can be found in 

enSuite

 under "

Parameterize online

" > "

Parameters

". 

Setting the input mode: 

 

Open the administration lock as described in the EK280 Operating Instructions. 

 

Move the cursor to the "

Serv.

" tab and via the path below go to the input mode "

Md.I1

": 

Serv. 

 Inputs 

 Input 1 

 Md.I1

 

 

Press the ENTER 

 button. The set value flashes.

 

 

Repeatedly press one of the 

 or 

 arrow keys until the text "

pulse input

" flashes.  

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key.

 

Setting the cp (pulse constant) value: 

 

Move the cursor to cp value "

cp.I1

" in the same path

 

 

Press the ENTER 

 button. One of the value's digits flashes.

 

 

Move the cursor to the digits using the 

 or 

 arrow keys and update them using the 

 or 

 arrow 

keys. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key.

 

 

Close the administration lock of the EK280. 

Set the counter value: 

 

If necessary, the meter reading of the gas meter can be set as the starting value for the volume at 
measurement conditions Vm. The procedure is described in Chapter "2.4.4".

 

 

Summary of Contents for EK280




































































































































































Reviews:

No comments