manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 101 / 163

Share
Download
Elster EK280 Applications Manual Download Page 101

EK280 

Application Manual 

99 

 

 

Remove the communication link between the PC / laptop and the Modem again. 

 

Disconnect the parameterizing cable from the modem assembly. 

 

Refit the "mode" jumper on the FE260 modem board in the "operation" position.  

 

7.3.6.6  EK280 data transfer activation 

 

Set up a communication link via the optical interface between enSuite and the EK280 (see chapter 
3.1 "Setting up the communication link to the EK280 via optical interface", page 15) again. 

 

Select "

Navigation

" on the left-hand side and then "

Parameterize online

" at the bottom of the 

navigation window.  

 

In the top of the device window open the path "

Parameters

" > "

Interfaces

" by clicking on the relevant 

plus signs, and then select "

Call time windows

". 

 

For call window 5 set the start to "00:00" and the end to "23:59" and then select the "Transfer 
changes to device" icon at the top of the enSuite window. 

 

Wait for around a minute for the EK280 to detect the FE260. 

 

7.3.6.7  Checking GSM field strength 

 

Move the cursor to the "

Serv.

" tab in the EK280's display, then to  

Interfaces > Terminal interface

 

> Hardware Config. > MdxS2

 

 

Press the 

ENTER

 key and using the keypad 

 set the value to "

GSM Wavecom

". 

 

Press the 

ENTER

 key to save the input. 

 

Move the cursor to the "

Serv.

" tab in the EK280's display, then to  

Interfaces > Terminal interface

 

> GSM & GPRS > GSM.L

 

 

Wait a few seconds until the field strength percentage is displayed under 

GSM.L

. 

 

i 

With a field strength below 50% data transfer issues may be encountered. Adjusting the antenna 
position can improve field strength in most cases. 

 

 

Move the cursor to the "

Serv.

" tab in the EK280's display, then to  

Interfaces > Terminal interface.

 

> Hardware Config. > MdxS2

 

 

Press the 

ENTER

 key and using the keypad 

 set the value to "

transparent

". 

 

Press the 

ENTER

 key to save the input. 

 

7.3.6.8  Monitoring data transfer to the FTP server 

Now you can check the data transfer to the FTP server using a suitable FTP client (i.e. "Filezilla"). Data should 
now  be  automatically  transferred  at  the  intervals  programmed  in  the  ComFTP  from  the  volume  conversion 
device to the server. 
 

 

Summary of Contents for EK280




































































































































































Reviews:

No comments