manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 152 / 163

Share
Download
Elster EK280 Applications Manual Download Page 152

EK280 

Application Manual 

150 

 

9.7 

Updates archive 

Attempted or completed updates of the device software are archived in the updates archive via an interface.  
The content of the update archive can be shown on the display of the device via the path

 

"Serv." > "Archives" 

> "Update archiv"

. 

 

i 

The update archive

 

is not a flexible archive.  

 

9.7.1 

Archive content 

Pos. 

Address 

Display 

Description 

Retrievable 

1

 

1 

01:01F8  GONo 

Global Block number 

S 

2 

08:0A20  ABNo 

Archive Block number 

A + S 

3 

01:0400  Time 

Date and time 

A + S 

4 

02:0197  NVers 

New firmware version 

A + S 

5 

01:0198_1  SigRL 

Firmware signature part 'R', low part 

A + S 

6 

01:0198_2  SigRH 

Firmware signature part 'R', high part 

A + S 

7 

02:0198_1  SigSL 

Firmware signature part 'S', low part 

A + S 

8 

02:0198_2  SigSH 

Firmware signature part 'S', high part 

A + S 

9 

08:0811  User 

User who started the firmware update 

A + S 

10 

08:0812  Reslt 

Result entries of the software updates

A + S 

11 

08:0A21  Check 

Check sum result  ( „CRC OK“ or „Error“) 

A + S 

1

  The  values  can  be  retrieved  in  accordance  with  the  information  in  the  table  via  D  =  display  and/or  

I = interface. 

9.7.2 

Memory capacity 

The archive can store the last 20 updates or update attempts on the device software. 

 

i 

The updates archive is not a ring-type memory.  
If the archive is full, then the archive must be deleted in order to carry out further updates or to 
attempt to do so (see Chapter 9.7.3).  

 

9.7.3 

Delete updates archive 

 

i 

The update archive

 

is also deleted via the function "

ClrV

" (see Chapter 2.4.2 

Clear volumes and 

archives ("Clr.V")

). 

 

 

So that the updates archive is deleted from the device, open the calibration lock as described in the 
EK280 operating instructions. 

 

Move the cursor to 

"Serv." 

>

 "Archives" > "ClrUL".

 

 

Press the ENTER button 

 "0" flashes.

 

 

Change the value using the arrow buttons 

 or 

 to 

"1"

. 

 

Press the ENTER button to confirm the set value. It is possible to abort the entry by pressing the 
ESC button. 

Summary of Contents for EK280




































































































































































Reviews:

No comments