manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 81 / 163

Share
Download
Elster EK280 Applications Manual Download Page 81

EK280 

Application Manual 

79 

 

 

 

 

Terminate the "ModemIni" program 

 

Now disconnect the power to EM260. 

 

Disconnect the parameterization cable from EM260 

 

On the modem adapter board, push-fit the jumper "Mode" in the position "operation" r.h. position, see 
photograph).  

 

Make sure that the EM260 is connected in accordance with Section 7.2.1 to the EK280. 

 

Make sure that a SIM card is inserted into the CSM modem. 

 

Make sure that a GSM antenna is connected to the modem. 

 

Close housing of EM260 

 

Switch on the power to the EM260. 

 

Approx. 1 minute after switching on, the GSM modem ought to have logged on in the GSM network and 
should be able to communicate which is indicated by the flashing yellow LED "online" on the EM260 
housing cover. 

 

7.2.4.3  Checking GSM field strength 

Before starting a data transfer via the modem, you must ensure that there is adequate reception field strength. 

a)  Opening the test time window on the device 

i 

The test time window only needs to be open if none of the time windows 5 to 6 is currently open. 

 

Move the cursor to the "

Serv.

" tab in the EK280's display, then to  

Interfaces > Terminal interface. > CWTst

 

 

Press the ENTER button in order to enter the length of the test time window in minutes 

 "

0

" 

flashes. 

 

Move the cursor with the arrow keys 

 or 

 to the digits and change these with the arrow keys 

 or 

 to 10, for example. 

 

After the desired digits have been changed, press the ENTER button in order to confirm the input. It 
is possible to abort the entry by pressing the ESC button. 

b) Display GSM field strength  

 

Move the cursor to the "

Serv.

" tab in the EK280's display, then to  

Interfaces > Terminal interface > GSM & GPRS > GSM.L

 

 

With the cursor over 

GSM.L

, please press the EK280 

ENTER

 button and wait for approximately 30 

seconds. 

 

The percentage field strength is now displayed under 

GSM.L

.  

 

i 

With a field strength below 50% data transfer issues may be encountered. You can remedy this in 
the majority of cases with an external antenna, mounted somewhere suitable. 

 

 

Summary of Contents for EK280




































































































































































Reviews:

No comments