manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 139 / 163

Share
Download
Elster EK280 Applications Manual Download Page 139

EK280 

Application Manual 

137 

 

c)  Configure message transmission 

 

With enSuite change to sub-menu "

SMS

" > "

Settings

" 

 

You can define up to 10 SMS messages, change to the related sub-menu "

SMS 1” 

up to

 

"SMS 10”

. 

 

 

After you changed EK280 parameters activate "

Transfer changes to device

" at the menu bar in enSuite. 

 

d)  Configure individual parameters 

To transmit a message as email of fax you have to configure abbreviated numbers (different for each 
mobile service provider). 
Use the enSuite menu "

Read and set single parameters

” 

 

 

i 

If your mobile service provider is not shown please contact your IT department. 

 

 

SMS 

Definition 

Event 

EK280 event, at occurrence the message will be transmitted. Within enSuite, press the 

 button and select a status, a unique event or a regular event from the list shown. 

NoRcv 

0 = no conn. (SMS is not active; will not be sent to any recipient) 
1 = Dest 1 or 2 (SMS will be sent only to the first recipient which is reachable) 
2 = Dest 1 and 2 (SMS will be sent to both recipients) 

LayNo 

SMS layout number in the range 1 

– 15 (see a)) 

Iface 

Interface 2 = serial interface or 3 = internal modem, where the GSM modem is connected. 

Rcv1, 2 

Receiver number related to EK280 phone book (see b)) 

Way1, 2 

0 = message will be sent as SMS 
1 = message will be sent as email 
2 = message will be sent as fax 

Delay 

Delay of transmission in minutes since event occurs. 

PrTyp 

7 = short SMS 

 in case of recipient is not able to display messages with more than 160 

characters. The message may be split into multiple short messages. 
8 = long SMS 

 in case of recipient is able to display concatenated messages with more 

than 160 characters. 

Address 

Definition 

2:739   
(if modem 
connected to serial 
interface) 
 
3:739   
(if internal modem) 

Abbreviated numbers for email gateway. Known numbers: 
Telecom-D1:   8000 
Vodafone-D2: 3400 
E-Plus:            7676245 
O2:                  6245 

2:73A   
(if modem 
connected to serial 
interface) 
 
3:73A   
(if internal modem) 

Abbreviated numbers for fax gateway. Known numbers: 
Telecom-D1:   99 
Vodafone-D2: 99 
E-Plus:            1551 
O2:                  329 

Summary of Contents for EK280




































































































































































Reviews:

No comments