manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 103 / 163

Share
Download
Elster EK280 Applications Manual Download Page 103

EK280 

Application Manual 

101 

 

7.3.8 

FE260 with Ethernet Adapter 

 

 
Modemadapterboard 73016717 V1.2  
with attached LAN cable 04115524 
 

 
Insys Ethernet module 
04407090 

 

 

 

Figure 16: Insys Ethernet adapter in the FE260

 

 

 
 
 
 
 

This interface card is used as an interface with your Ethernet LAN. 

 

Initial conditions: 

 

The FE260 is connected as described in Chapter 7.3.1. It is connected but it must not be live. 

 

The Ethernet modem may be used for Modbus communication, for example (see Section 8.1). 
 

i 

There are separate instructions [9] for commissioning an EF260 which are supplied with every 
FE260!  

 

7.3.8.1  Parameterization of the EK280 for operation with an FE260/Ethernet 

i 

For parameterization of the EK280 you will require a connection cable for the optical interface as 
well as the enSuite application, which can be downloaded for free at www.elster-instromet.com. 

a) 

Closing the time windows 

In  order  that  the  parameterization  works  correctly  the  time  windows  5  and  6  must  be  closed.  Proceed  as 
described in Section 7.2.2.1 on page 69 . 

b) 

Send parameter file 

 

Send the following parameter file to the EK280 (see Chapter 3.6, page 17): 

EK280_xvx. - FE260 & int. Ethernet adapter (*)

 

14

  

 

For any further individual settings and tests required, press "

Navigation

" on the left-hand side and 

then "

Parameterize online

" at the bottom of the navigation window. 

                                                      
 

14

   The "x" stands for the version of software on the device, e.g. "2v2". 

The star * stands for a small letter which indicates the version of the file, e.g. "a". 

Summary of Contents for EK280




































































































































































Reviews:

No comments