manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 118 / 163

Share
Download
Elster EK280 Applications Manual Download Page 118

EK280 

Application Manual 

116 

 

7.5 

Data transfer verification 

Before the actual data transmission, the communication link,(e.g., call window, modem used) for a destination 
must be specified. Eight separate connections can be programmed.  

 

i 

For parameterization of the EK280 you will require a connection cable for the optical interface as 
well as the enSuite application at least with version 2.4, which can be downloaded for free at 
www.elster.com. 

 

The paths which are subsequently described can be found in the 

enSuite

 program under 

 "

Parameterize online

" > "

Parameters

" > "

Interfaces

". 

 

All connections are inactive as per factory settings and are preset as follows: 

Connection 

Event type 

Interface 

Power supply 

1 

Time window 

internal modem 

Battery 

2 

Time window 

internal modem 

Battery 

3 

Time window 

internal modem 

ext. Power supply 

4 

Time window 

internal modem 

ext. Power supply 

5 

Time window 

Terminal / ext. Modem 

ext. Power supply 

6 

Time window 

Terminal / ext. Modem 

ext. Power supply 

7 

Time 

internal modem 

always 

8 

Time 

internal modem 

always 

 

7.5.1 

Time window connection 

The major parameters for activating a time window connection are listed below. 
For parameterizing, use the enSuite program and change over to the sub-menu "

Connections" 

> 

"

Connection 1 to 6

". 

Time 

window 

connection 

Meaning 

cycle 

Cycle of a regular time window connection (e.g. hourly, daily, weekly, monthly) 

start 

Start of a time window connection (e.g. daily at 00:00, or another time) 

end 

End of a time window connection (e.g. daily at 11:59 PM, or another time) 

StCon 

Current status of this connection 

If the conditions for activating the time window connection are satisfied, then the interface is opened and the 
EK280 is ready to act as a recipient. If a modem is connected to this interface then the EK280 is only ready to 
act as a recipient after a further 30 seconds. 

The conditions for activating a time window connection are: 

- 

Is the current device time within the time window which has been parameterized? 

- 

Does the supply to the EK280 correspond with the parametrization of the connection? 

 

 

 

 

 

Summary of Contents for EK280




































































































































































Reviews:

No comments