manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 94 / 163

Share
Download
Elster EK280 Applications Manual Download Page 94

EK280 

Application Manual 

92 

 

  

Jumper "Mode" in Position "program" (lower position) 

 

 

 

Modem parameterization interface 

 

 

Connect a COM interface of your computer with the modem parameterization interface on the modem 
adapter board (see photograph) with the aid of a DSUB9-RS232 cable. 

 

Turn on the FE260 power supply. 

 

CAUTION! 230 V alternating current Risk to life! 

The following steps are performed in the same way during parameterization either on location or with GSM-
CSD modem connection. 

 

On your computer, start the program "WinPADS200-EK" (from version V2.99) 

 

In WinPADS, depending on the connection, select 

"Action"

 

 

"

Start connection via” 

 

 

"Local 

connection"

 or 

"Modem"

: 

 

 

 

 

Tick 

"Configure modem"

 or 

"

 

Configure remote modem" 

and choose the application 

"ComTCPserv"

:

 

Summary of Contents for EK280




































































































































































Reviews:

No comments