manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 120 / 163

Share
Download
Elster EK280 Applications Manual Download Page 120

EK280 

Application Manual 

118 

 

- 

Has the device time currently exceeded the parameterized point in time? 

- 

Does the supply to the EK280 correspond with the parametrization of the connection? 

- 

Is there a  valid telephone  number or IP address and  the port of the recipient parameterized  within the 
associated telephone book entry? 

 

7.5.3 

Connection configuration status "StCon"  

 

Display  Description 

0 

Establishment of a connection has not yet started. 

2 

The interface is activated specifically for the connection. 

3 

The interface to be used for the connection (i.e. the modem) is busy, the EK280 will wait until 
connection can be established.   
Either the interface has just been used for another connection or the EK280 is waiting to try 
again after a failed connection attempt. 
This state may persist for several minutes. 

4 

The interface (i.e. the modem) is ready to establish a connection (i.e. the call time window is 
open). 

5 

The interface is released specifically for the connection. 

6 

The interface (i.e. the modem) is released from other connections for use. (i.e. when the time 
window is no longer open) 

7 

Data transfer via DLMS protocol is in progress. 

8 

Data transfer via DLMS protocol is complete. 

9 

Data transfer via Modbus protocol is in progress. 

10 

Data transfer via Modbus protocol is complete. 

11 

Data transfer via LIS200 protocol is in progress. 

12 

Data transfer via LIS200 protocol is complete. 

13 

The EK280 is synchronizing with the EIServer, in readiness to begin data transfer via DLMS 
protocol. 

14 

EIServer synchronization is complete. 

15 

Data transfer via SMS is in progress. 

19

 

16 

Data transfer via SMS is complete. 

19

 

29 

No valid recipient specified. 

30 

A communication error occurred. 
This message is shown for example, if a modem to be used has no power supply. 

31 

The modem's supply voltage is too low. 

32 

The modem cannot be used due to SIM card error (modem message: "SIM Error") 

33 

The modem cannot be used as an incorrect PIN has been entered.  

34 

The modem cannot be used as an incorrect PUK has been entered. 

35 

Communication link to the network cannot be established or the communication link to the 
network was lost, before the communication link to the remote site could be established. 

36 

Communication link to the GSM network was denied. 

37 

The APN parameters required to establish a GPRS communication link are missing.

20

 

38 

Communication link to APN

 20

 was denied. 

                                                      
 

19

 SMS only available from Software Version 2.20 or later 

20

 APN = "Access Point Name" 

Summary of Contents for EK280




































































































































































Reviews:

No comments