Elster EK280 Applications Manual Download Page 86

Page: 86 / 163

EK280

Application Manual

7.3.2.2 SIM in GSM/GPRS module Integra "M2106+" or "M2106B"

a) SIM card insertion

Danger!

Ensure the mains voltage is disconnected before opening the FE260 housing, ensure it
is not turned back on and verify that there is no voltage.



Remove the four screws from the top of the FE260 and open it.



Ensure that the "JP2" (mode) jumper is in the "operation" position.



Press the eject button with for example a ballpoint pen or similar, to remove the SIM card slider.



Insert the SIM card into the card slot (i.e. the SIM carriage) so that the gold-plated contact face
upwards. the chamfered corner of the SIM card is at the bottom left (as illustrated on the print)



Push the SIM card and slider back into the modem until the slider clicks into place.



Screw the FE260 housing back on.

b) If necessary, unlock the SIM card (enter the PIN)

See Chapter 7.3.2.1 paragraph "b)".

Jumper "

JP2

" ("

Mode

in the uppermost
position "

operation

Integra M2106+

GSM antenna connection

Figure 12:

Integra modem with SIM

card slot

SIM card slot

Press the button to open
the SIM card slider.

Summary of Contents for EK280




































































































































































Search results

Summary of Contents for EK280

Reviews:

Elster EK280, Applications Manual, Page: 86 / 163

Search results

Summary of Contents for EK280

Reviews: