10 Communications
iConnect
Installation Manual
63
10.7.6.
GSM Media Loss Time
The GSM Media Loss Time is a feature that is designed to control the amount of GSM media loss events registered in
the log and sent to the central station.
If, for a period defined in GSM ML Time parameter, the GSM signal has always been below the lower threshold, a
Media Loss event is registered in the log and sent to the central station.
The GSM Media Loss event is sent to the central station via PSTN only.
If, for a period defined in GSM ML Time parameter, since GSM media restore is detected, the GSM signal has always
been above the upper threshold, GSM Media Restore is registered in the log and sent to central station.
To disable the GSM Media Loss feature (cancel the GSM Media Loss events) enter 000.
To program the GSM Media Loss Time:
1.
From the Programming menu, select Communications, Comm. Options, GSM Options, GSM ML Time. [954126].
2.
Enter time (003-255 minutes or 000 to disable), then press '
√ʹ.
10.8.
TWA Event Report Options
10.8.1.
TWA Event Report
The TWA Event Report is an event report that is sent to the central station to indicate that Two-Way Audio
communication is about to commence. If enabled, the system sends the Contact ID event code 606000 before
establishing Two-Way Audio communication.
This option affects Contact ID only. If using SIA, a TWA event report is always sent together
with the TC/VM timeout, regardless of the configuration for this option.
To program the TWA Event option:
1.
From the Programming menu, select Communications, Comm. Options, TWA Event Rept. [95413].
2.
Select Enabled or Disabled.
10.8.2.
TWA Time Report
If the TWA Time Report option is enabled, the last three digits of the TWA Event Report are replaced with the amount
of seconds programmed for the TC/VM Timeout – p. 61,
10.6.9 Telecontrol/Vocal Message Timeout. For example, if the
TC/VM Timeout is programmed as 120 seconds, the Contact ID event code to be sent for the TWA Event Report will be
606120.
To program the TWA Time Report option:
1.
From the Programming menu, select Communications, Comm. Options, TWA Time Rept. [95414].
2.
Select Enabled or Disabled.
10.8.3.
Incoming Number
Incoming number feature allows the installer to program up to three high-priority telephone numbers so that the user
would be able to use Telecontrol/2-way audio over GSM during a GPRS session. If the Control System recognizes the
incoming call as a high-priority call, the GPRS session will be suspended.
To program/edit the Incoming Number:
1.
From the Programming menu, select Communications, Comm. Options, Incoming #. [95415].
2.
Select the telephone number you want to edit (1-3).
3.
Enter up to 16 digits. Use the key to enter "
", "#", "," (pause), "T" (switch to DTMF tone dialing), "P" (switch to
pulse dialing) or "+" (international code). Use the key to delete one character at a time. Press '
√ʹ when you
have finished editing.
10.8.4.
Remote Firmware Update
Electronics Line 3000’s Remote Firmware Update feature allows the Installer or service provider to perform firmware
update from a remote PC using WEB communication.
Before performing the firmware update, locally disarm the system and make sure that there
are no AC LOSS or BATTERY LOW conditions.
Summary of Contents for iconnect
