Dynapac CC950 Instruction Manual Download Page 98

Page: 98 / 143

Maintenance, 10h

4812164101_A.pdf

2022-02-09

Brakes - Check

Check operation of the brakes as follows:

Checking the parking brake

Fig. Control panel
1. Parking brake
2. Parking brake lamp

Drive the roller slowly forward. Hold the steering wheel
firmly and brace yourself for a sudden stop.

Enable the parking brake (1). The roller should stop
immediately with the engine running.

After testing the brakes, set the forward/reverse lever
in neutral.

Reset the parkering brake (1).

The roller is now ready for operation.

Refer also to the section in the manual on operation.

Checking the emergency stop

Fig. Emergency stop

Drive the roller slowly forward. Hold the steering wheel
firmly and brace yourself for a sudden stop.

Press the emergency stop (7).
The roller will stop abruptly and the engine will be
switched off.

After testing the brakes, set the forward/reverse lever
in neutral.

Pull out the emergency stop (7) and start the engine.

The roller is now ready for operation.

Refer also to the section in the manual on operation.

Summary of Contents for CC950
















































































































































Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands

Dynapac CC950, Instruction Manual

Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands