Dynapac CC950 Instruction Manual Download Page 90

Page: 90 / 143

Maintenance, 10h

4812164101_A.pdf

2022-02-09

Hydraulic reservoir cap - Check

Unscrew and make sure that the reservoir cap is not
blocked. Air must have unobstructed passage through
the cap in both directions.

Fig. Engine compartment,
right side
1. Hydraulic fluid tank cap
2. Hydraulic oil level

If blocked in either direction, clean with a little diesel oil
and blow with compressed air until unblocked or
replace the cap with a new one.

When working with compressed air, use the
following protective equipment:

Safety glasses

Protective gloves

Ear protectors

Fig. Control panel
2. Parking brake
4. Control panel

Warning lamps - Check

Check that the warning lamp on the control panel is
functional (4).

Summary of Contents for CC950
















































































































































Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands

Dynapac CC950, Instruction Manual

Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands