Dynapac CC950 Instruction Manual Download Page 129

Page: 129 / 143

Maintenance - 1000h

4812164101_A.pdf

2022-02-09

Valve gasket - Change

Be sure the reinstall the detached safety shield
after maintenance or checking.

Use caution. Use the following protective
equipment:

Protective gloves

Refer to the engine manual for detailed
instructions.

Belt tension on the hydraulic vibration and
steering pump drive belt - Check

Fig. Engine compartment
1. Screw
2. Screw

If the hydraulic pump drive belt can be pressed in 5-6
mm between the pulleys with a force of 50 Nm, then
the belt is correctly tensioned.

Do as follows to tension the belt:

- Undo the screws (1) and (2).

- Press over the hydraulic pump so that the belt
tensions to the specified extent.

- Tighten screw (1) and then screw (2).

- Check that the belt still has the correct tension after
tightening.

Replace the belt when necessary, or after 2000 h.

119

Summary of Contents for CC950
















































































































































Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands

Dynapac CC950, Instruction Manual

Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands