Miscellaneous
4812164101_A.pdf
2022-02-09
-
The contact surfaces must be clean, wet or dry, and free from frost, ice and snow. If there is a
risk of frost, ice and/or snow the platform has to be salted.
-
The contact surfaces must be clean, wet or dry, and free from frost, ice and snow. If there is a
risk of frost, ice and/or snow the platform has to be salted.
-
The lashing mounts on the load carrier have LC/MSL at least 2 tonnes.
-
The lashing mounts on the load carrier have LC/MSL at least 2 tonnes.
Lashings
Lashings
Ensure that:
Ensure that:
-
The lashings comprise a lashing strap or chain with a permitted load (LC/MSL) of at least 1.6
tonnes (1,600 daN) and the lashings are well pre-tensioned during the entire transport.
-
The lashings comprise a lashing strap or chain with a permitted load (LC/MSL) of at least 1.6
tonnes (1,600 daN) and the lashings are well pre-tensioned during the entire transport.
-
Each of lashings 1-2 is either a double or two single lashings. A double lashing runs in a sling
through a lashing point or around a machine part and down into two different mounts on the
platform.
-
Each of lashings 1-2 is either a double or two single lashings. A double lashing runs in a sling
through a lashing point or around a machine part and down into two different mounts on the
platform.
-
Lashings in the same direction are placed in different lashing mounts on the trailer. Lashings
that are pulled in opposite directions may be placed in the same lashing mount, however.
-
Lashings in the same direction are placed in different lashing mounts on the trailer. Lashings
that are pulled in opposite directions may be placed in the same lashing mount, however.
-
The lashings are as short as possible.
-
The lashings are as short as possible.
-
The lashing hooks must not lose grip if the lashings become slack.
-
The lashing hooks must not lose grip if the lashings become slack.
-
The lashings are protected against sharp edges and corners.
-
The lashings are protected against sharp edges and corners.
-
The lashings are located symmetrically in pairs on the right and left sides.
-
The lashings are located symmetrically in pairs on the right and left sides.
56
Summary of Contents for CC950
