Dynapac CC950 Instruction Manual Download Page 58

Page: 58 / 143

Operation

4812164101_A.pdf

2022-02-09

Emergency stop

Fig. Emergency stop

The emergency stop is activated by pressing the
button (7).

Hold the steering wheel firmly and brace yourself for a
sudden stop.

The brake is applied and the engine stops.

After an emergency stop, return the forward/reverse
lever to neutral and deactivate the emergency stop by
pulling out the button (7).

Switching off

Turn the engine speed control (16) back to idling.
Allow the engine to idle for few minutes to cool.

Activate the parking brake (2).

Turn the starter switch (8) to the left to shut off position.

Fig. Control panel
- Non-pressurized sprinkler system
2. Parking brake
8. Starter switch
16. Engine speed control

Fig. Control panel
- Pressurized sprinkler system
2. Parking brake
8. Starter switch
16. Engine speed control

Summary of Contents for CC950
















































































































































Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands

Dynapac CC950, Instruction Manual

Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands