Dynapac CC950 Instruction Manual Download Page 67

Page: 67 / 143

Miscellaneous

4812164101_A.pdf

2022-02-09

Securing
CC950 for loading (Side along the trailer)

Securing of two CC950 vibratory rollers from Dynapac
loaded side by side along a trailer for transport on road
and in Baltic sea (Sea area A).

Direct of travel

1 - 2 = double lashings, i.e. one lashing with two parts secured to two different lashing mounts on

the trailer. Symmetrically located on the right and left sides.

1 - 2 = double lashings, i.e. one lashing with two parts secured to two different lashing mounts on

the trailer. Symmetrically located on the right and left sides.

= wooden battens used as spacers between the rollers, kept in place by sufficient means

= the two rollers are tied together to one unit.

= rubber friction pads

The lashings' permitted distance interval in meters

(1 - 2: Double lashings, LC at least 1.6 tonnes (1600 daN)

Double L

0,1 - 2,5

1,0 - 2,5

0,1 - 2,5

1,0 - 2,5

and

are the longitudinal distances between the lashing points on the roller and lashing points on the platform.

and

are the longitudinal distances between the lashing points on the roller and lashing points on the platform.

Summary of Contents for CC950
















































































































































Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands

Dynapac CC950, Instruction Manual

Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands