Dynapac CC950 Instruction Manual Download Page 127

Page: 127 / 143

Maintenance - 1000h

4812164101_A.pdf

2022-02-09

Hydraulic fluid filter - Change

Fig. Engine compartment, left side
1. Hydraulic fluid filter

Remove the filter (1) and deliver to special
waste handling. This is a single-use filter and
cannot be cleaned.

Thoroughly clean the filter holder sealing surface.

Apply a thin coat of fresh hydraulic fluid to the rubber
gasket on the new filter.

Screw the filter on by hand, firstly until the filter gasket
makes contact with the filter base. Then rotate a
further ½ turn.

Start the engine and check that the filter does not leak.

Do not over-tighten. The seal can be damaged.

Dispose of the old filter carefully.

Steering joint - Check

Fig. Steering joint

Inspect the steering joint to detect any
damage or cracks.

Check and tighten any loose bolts.

Check also for any stiffness and play in the steering
joint. Rectify if necessary.

117

Summary of Contents for CC950
















































































































































Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands

Dynapac CC950, Instruction Manual

Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands