Dynapac CC950 Instruction Manual Download Page 92

Page: 92 / 143

Maintenance, 10h

4812164101_A.pdf

2022-02-09

Sprinkler system - Check, cleaning

Fig. Sprinkler system
1. Sprinkler pipes with holes for water.

Check that the holes in the sprinkler pipe (1) are not
clogged, clean if necessary.

Fig. Sprinkler system - Pressurized
1. Sprinkler nozzles

On machine with pressurized sprinkler system:

Check that the holes in the sprinkler nozzles (1) are
not blocked. Clean where necessary.

Check that the water filter (2) is not blocked. Clean
where necessary.

Clean the water filter by unscrewing the filter’s lower
section, and clean the strainer and filter housing.

Reassemble in the reverse order.

Fig. Sprinkler system - Pressurized
2. Water filter

Summary of Contents for CC950
















































































































































Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands

Dynapac CC950, Instruction Manual

Search results

Summary of Contents for CC950

Reviews:

Related manuals for CC950

Brands by name

Popular brands