manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

INSTALLATION OF RADIO TRANSMITTING

EQUIPMENT

Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained personnel.
The following must be observed during installation.

The positive power connection should be made directly to
the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.

Antennas for two-way radios should be mounted on the roof
or the rear area of the vehicle. Care should be used in
mounting antennas with magnet bases. Magnets may affect
the accuracy or operation of the compass on vehicles so
equipped.

The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.

Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).

Mobile radio equipment with output power greater than
normal may require special precautions.

All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Porsche Carrera GT Manual preview
Carrera GT
Brand: Porsche Pages: 192
FormFit HD 23A 07 Installation Instructions preview
HD 23A 07
Brand: FormFit Pages: 4
UGREEN Car Cup Holder Phone Mount Manual preview
Car Cup Holder Phone Mount
Brand: UGREEN Pages: 9
Audiovox Code Alarm PROFESSIONAL SERIES CA 5550SST Owner'S Manual preview
Code Alarm PROFESSIONAL SERIES CA 5550SST
Brand: Audiovox Pages: 14
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Brand: Voxoa Pages: 48
Flash Cover MN019 Instructions preview
MN019
Brand: Flash Cover Pages: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Brand: Porsche Pages: 98
Mercedes-Benz CLS 2015 Operator'S Manual preview
CLS 2015
Brand: Mercedes-Benz Pages: 398
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Brand: Brodit Pages: 2
Summit Racing SUM-G1083 Assembly & Use Instructions preview
SUM-G1083
Brand: Summit Racing Pages: 11
Mazda MX-3 1995 Workshop Manual preview
MX-3 1995
Brand: Mazda Pages: 1001
Coolster CHALLENGER GK-6125A 2018 Manual preview
CHALLENGER GK-6125A 2018
Brand: Coolster Pages: 45
Audiovox Prestige 128-8602 Installation Manual preview
Prestige 128-8602
Brand: Audiovox Pages: 8
SSV Works RG4-DM3 Manual preview
RG4-DM3
Brand: SSV Works Pages: 2
Motoalliance Denali MA11737 Manual preview
Denali MA11737
Brand: Motoalliance Pages: 4
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9
Pyle PLPSC8 User Manual preview
PLPSC8
Brand: Pyle Pages: 14
Genesis GV60 2023 Owner'S Manual preview
GV60 2023
Brand: Genesis Pages: 690

Brands by name

Popular brands

Load more brands