Dodge avenger 2013 Owner'S Manual Download Page 95 | Manualshive

Page: 95 / 631

background image

8. If the child restraint has a top tether strap and the

seating position has a top tether anchorage, connect
the tether strap to the anchorage and tighten the tether
strap. Refer to “Lower Anchors and Tethers for Chil-
dren (LATCH) Restraint System” for directions to
attach a tether anchor.

9. Test that the child restraint is installed tightly by

pulling back and forth on the child seat at the belt
path. It should not move more than 1 inch (25.4 mm)
in any direction.

Any seat belt system will loosen with time, so check the
belt occasionally, and pull it tight if necessary.

Installing A Child Restraint With A Cinching
Latch Plate (CINCH) — If Equipped

1. Place the child seat in the center of the seating

position. For some second row seats, you may need to
recline the seat and / or raise the head restraint to get
a better fit.

2. Next, pull enough of the seat belt webbing from the

retractor to pass it through the belt path of the child
restraint. Do not twist the belt webbing in the belt
path.

3. Slide the latch plate into the buckle until you hear a

“click.”

4. Finally, pull up on any excess webbing to tighten the

lap portion around the child restraint while you push
the child restraint rearward and downward into the
vehicle seat.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

93

«
...
93
94
95
96
97
...
»

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Brand: RACLET Pages: 48

Brand: RACLET Pages: 31

Brand: Vauxhall Pages: 199

Brand: Vauxhall Pages: 323

Brand: Ford Pages: 8

Brand: Intec Pages: 16

Brand: Vauxhall Pages: 259

TRI-FOLD PG9300RF

Brand: Pet Gear Pages: 4

Brand: GMC Pages: 430

51 47 0 027 792

Brand: BMW Pages: 7

Brand: Ford Pages: 728

Brand: Westin Pages: 5

CARWATT CV12-220C150

Brand: WATT Pages: 26

Brand: Mercedes-Benz Pages: 10

Brand: Thule Pages: 4

Brand: Jaeger Pages: 16

Brand: Saab Pages: 288

Brand: Fabbri Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands