manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

2. Move to the outside of the vehicle and push the safety

catch to the left. The safety catch is located under the
center front edge of the hood.

CAUTION!

To prevent possible damage, do not slam the hood to
close it. Lower the hood until it is open 8 in (20 cm)
approximately and then drop it. This should secure
both latches. Never drive your vehicle unless the
hood is fully closed, with both latches engaged.

WARNING!

Be sure the hood is fully latched before driving your
vehicle. If the hood is not fully latched, it could open
when the vehicle is in motion and block your vision.
Failure to follow this warning could result in serious
injury or death.

Hood Safety Catch

218

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Brand: Gatorback Mudflaps Pages: 4
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Brand: Mercedes-Benz Pages: 54
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Brand: Ecco Pages: 12
GMC 2013 GMC Savana Owner'S Manual preview
2013 GMC Savana
Brand: GMC Pages: 398
Curt Group 60638 Installation Manual preview
60638
Brand: Curt Group Pages: 3
Juna JRDAB-03 Installation Manual preview
JRDAB-03
Brand: Juna Pages: 10
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Brand: Kleinn Air Horns Pages: 33
Whispbar K408W Fitting Instructions Manual preview
K408W
Brand: Whispbar Pages: 15
Prorack K442 Fitting Instructions Manual preview
K442
Brand: Prorack Pages: 15
SAF-HOLLAND SK-V 20 Mounting, Operation And Maintenance preview
SK-V 20
Brand: SAF-HOLLAND Pages: 22
Honda 2013 Civic Coupe Technology Reference Manual preview
2013 Civic Coupe
Brand: Honda Pages: 13
Toyota 2004 CELICA Electric Troubleshooting Manual preview
2004 CELICA
Brand: Toyota Pages: 284
CARPOD M2205 Assembly And Operating Instructions preview
M2205
Brand: CARPOD Pages: 2
Whispbar K144W Fitting Instructions Manual preview
K144W
Brand: Whispbar Pages: 78
Autostart DS4+ Quick Start User Manual preview
DS4+
Brand: Autostart Pages: 1
Edscha Trailer Systems CS-Profi Repairing Instructions preview
CS-Profi
Brand: Edscha Trailer Systems Pages: 42
MayPole MP68158 Assembly Instructions preview
MP68158
Brand: MayPole Pages: 2
Maxxair MAXXFAN Deluxe Series Installation Instructions, Information And Operating Manual preview
MAXXFAN Deluxe Series
Brand: Maxxair Pages: 8

Brands by name

Popular brands

Load more brands