manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

CAUTION!

To avoid damage to your vehicle or tires, observe the
following precautions:

•

Because of restricted traction device clearance be-
tween tires and other suspension components, it is
important that only traction devices in good condi-
tion are used. Broken devices can cause serious
damage. Stop the vehicle immediately if noise
occurs that could indicate device breakage. Remove
the damaged parts of the device before further use.

•

Install device as tightly as possible and then re-
tighten after driving about ½ mile (0.8 km).

(Continued)

CAUTION!

(Continued)

•

Do not exceed 30 mph (48 km/h).

•

Drive cautiously and avoid severe turns and large
bumps, especially with a loaded vehicle.

•

Do not drive for prolonged period on dry pave-
ment.

•

Observe the traction device manufacturer’s instruc-
tions on the method of installation, operating speed,
and conditions for use. Always use the suggested
operating speed of the device manufacturer’s if it is
less than 30 mph (48 km/h).

•

Do not use traction devices on a compact spare tire.

464

STARTING AND OPERATING

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Brand: Mazda Pages: 4
AA Products X31 Instruction Manual preview
X31
Brand: AA Products Pages: 6
Dakota Digital VHX-37F Installation preview
VHX-37F
Brand: Dakota Digital Pages: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Brand: Dakota Digital Pages: 7
Yakima K343 Manual preview
K343
Brand: Yakima Pages: 11
Globalsat MR-350P Installation Manual preview
MR-350P
Brand: Globalsat Pages: 2
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Brand: STO N SHO Pages: 7
Fab Fours H4550 Installation Instructions Manual preview
H4550
Brand: Fab Fours Pages: 13
Volvo 2006 XC70 Owner'S Manual preview
2006 XC70
Brand: Volvo Pages: 211
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Brand: SilverLeaf Electronics Pages: 16
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Brand: Whelen Engineering Company Pages: 2
Classic AutoAir Mustang 1969 Installation Manual preview
Mustang 1969
Brand: Classic AutoAir Pages: 44
Aries 2051182 Installation Manual preview
2051182
Brand: Aries Pages: 3
Alfa Romeo Stelvio 2019 User Manual preview
Stelvio 2019
Brand: Alfa Romeo Pages: 268
Hamron 012463 Operating Instructions Manual preview
012463
Brand: Hamron Pages: 6
Lincoln MKZ HYBRID 2016 Quick Reference Manual preview
MKZ HYBRID 2016
Brand: Lincoln Pages: 10

Brands by name

Popular brands

Load more brands