manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

To Exit Remote Start Mode And Drive The Vehicle

Before the end of 15 minute cycle, press and release the
UNLOCK button on the RKE transmitter to unlock the
doors and disarm the Vehicle Security Alarm (if equipped).
Then, prior to the end of the 15 minute cycle, press and
release the START/STOP button.

NOTE:

The message “Push Start Button” will display in

the EVIC until you push the START button.

Cancel Remote Start

Remote Starting will also cancel if any of the following
occur:

•

The engine stalls or engine speed exceeds 2500 rpm

•

Any engine warning lights come on

•

Low Fuel Light turns on

•

The hood is opened

•

The hazard switch is pressed

•

The shift lever is moved out of PARK

•

The brake pedal is pressed

DOOR LOCKS

Manual Door Locks

To lock each door, push the door lock knob on each door
trim panel downward. To unlock the front doors, pull the
inside door handle to the first detent. To unlock the rear
doors, pull the door lock knob on the door trim panel
upward.

30

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
Carefree Slideout Cover Service Manual preview
Slideout Cover
Brand: Carefree Pages: 12
ABL Wallbox eM4 Single Installation Manual preview
Wallbox eM4 Single
Brand: ABL Pages: 68
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Brand: Safe Fleet Pages: 12
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Brand: Harman Kardon Pages: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Brand: TATA Motors Pages: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Brand: B&G electronics Pages: 7
Kargo Master 8006A Instruction Manual preview
8006A
Brand: Kargo Master Pages: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Brand: Safe Fleet Pages: 12
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Brand: r.LiNK Pages: 21
Rugged Ridge 11232.20 Quick Start Manual preview
11232.20
Brand: Rugged Ridge Pages: 2
Westfalia 859528 Original Instructions Manual preview
859528
Brand: Westfalia Pages: 10
Ford Escape 2022 Owner'S Manual preview
Escape 2022
Brand: Ford Pages: 585
Lexus 2010 RX 350 Warranty And Services Manual preview
2010 RX 350
Brand: Lexus Pages: 82
Edelbrock 5756 Installation Instructions preview
5756
Brand: Edelbrock Pages: 1
Sintrones SBOX-2320 User Manual preview
SBOX-2320
Brand: Sintrones Pages: 55
Flash Cover MN012 Installation Manual preview
MN012
Brand: Flash Cover Pages: 2
ROLEC WallPod Series Installation Instructions preview
WallPod Series
Brand: ROLEC Pages: 2

Brands by name

Popular brands

Load more brands