Dodge avenger 2013 Owner'S Manual Download Page 470 | Manualshive

Page: 470 / 631

background image

NOTE:

•

The TPMS is not intended to replace normal tire care
and maintenance or to provide warning of a tire failure
or condition.

•

The TPMS should not be used as a tire pressure gauge
while adjusting your tire pressure.

•

Driving on a significantly under-inflated tire causes
the tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency and tire
tread life, and may affect the vehicle’s handling and
stopping ability.

•

The TPMS is not a substitute for proper tire mainte-
nance, and it is the driver’s responsibility to maintain
correct tire pressure using an accurate tire pressure
gauge, even if under-inflation has not reached the level
to trigger illumination of the TPM Telltale Light.

•

Seasonal temperature changes will affect tire pressure,
and the TPMS will monitor the actual tire pressure in
the tire.

Base System

The Tire Pressure Monitor System (TPMS) uses wireless
technology with wheel rim mounted electronic sensors to
monitor tire pressure levels. Sensors mounted to each
wheel as part of the valve stem transmit tire pressure
readings to the receiver module.

468

STARTING AND OPERATING

«
...
468
469
470
471
472
...
»

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Brand: Suzuki Pages: 16

Brand: Baja Designs Pages: 6

Brand: Dometic GROUP Pages: 20

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Autostacker PL-6SR

Brand: BendPak Pages: 104

Brand: Easee Pages: 12

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

Brand: BraunAbility Pages: 46

Brand: Summit Racing Pages: 11

Brand: Kuda-Phonebase Pages: 3

spectroFlex Car Adapter

Brand: wtw Pages: 4

Brand: Lexus Pages: 878

ASENTO EV-COLC15R

Brand: ADAPT SOLUTIONS Pages: 22

Brand: Stack Pages: 4

Brand: AutoMaxi Pages: 2

Brand: Kleinn Air Horns Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands